
PR-84-DB-TW
Scari Super Seeder (50mm wing) has tungsten carbide wear protection on the leading edge and underside of the wing.
Requires one 2 1/2″ x 1/2″ UNF G8 UNC bolt and nyloc PLUS a PAC-84 tine clip to suit the scarifier tine.
Note the top hole in the point requires the original riveted tine clip to be ground off the tine and replaced with a PAC-84-series tine clip.

PR-11-T
2 ½” Ripper T.C. tipped

PR-12-T
6” Buster T.C. tipped

#PAC-84-1
Suits Shearer, MF, IH
includes 1 1/2″ x 3/8″ C/H bolt & nyloc , flat washer and 1 1/2″ x 1/4″ G5 UNC hex bolt & Nyloc.

#PAC-84-2
Suits CJD 300, FE 350
includes 1 1/2″ x 3/8″ C/H bolt & nyloc , flat washer and 1 1/2″ x 3/8″ G5 UNC hex bolt & Nyloc.

# PAC-84-3
Suits CS Scariseeder
includes M10 x 40 G8.8 Hex bolt & nyloc , flat washer and 1 1/4″ x 1/4″ G5 UNC hex bolt & Nyloc.

#PAC-84-4
Suits H.B. Scarimaster
includes 1 3/4″ x 3/8″ C/H bolt & nyloc , flat washer and 1 3/4″ x 3/8″ G5 UNC hex bolt & Nyloc.

PR-25-T
(Run out stocks Only)
9” Low profile sweep T.C. tipped

PR-14-T
8” Low-profile sweep T.C. tipped

PR-13-T
7” Sweep T.C. tipped

PR-26-T
(Run out Stocks Only – get in quick )
2.5” T.C. tipped to suit HB Scaribar and Stubblemaster ( Series 1 and 2)
Requires one 2 1/2″ x 5/8″ G8 Bolt and Nyloc torqued to 110Nm ( 80 lb ft)

PR-27-T
(Run out Stocks only -get in quick)
8” T.C. tipped to suit HB Scaribar and Stubblemaster ( Series 1 and 2)
Requires one 2 1/2″ x 5/8″ G8 Bolt and Nyloc torqued to 110Nm ( 80 lb ft)

ST-SBEO-2
SINGLE SHOOT BRACKET to allow fitment of rubber flexi boot and tail
Requires a suitable ST-CB tine clip and 1″ x 5/16″ UNC Z/P bolt and nyloc
PASTURE Renovation

PR-93
“Baker” T-Boot with tungsten carbide on leading edge. (60mm bolt centres)
Use two 1 1/2″ x 5/16″ UNC G5 z/p bolt and nylocs for Connor Shea Coil Tine coulter Drill
Use two M10 x 30 G8.8 Z/P bolts and nylocs for Agro Drill or Duncan Drill and two 1 3/4″ x 5/16″UNC G5 Bolt and Nyloc for Aitchison (NZ) Drill.
(Tungsten carbide in the wings is an optional extra under part number PR93-TW)

PR-92M
Mini T-Boot with tungsten carbide on leading edge. (32mm bolt centres)
Use two 1″ x 5/16″ UNC G5 z/p bolt and nylocs for Begg, Shearer Tine Drill, Sod Seeder coulter Tine Drill, Trash Culti Drill, all other machines converted with “Caldow” tine adaptors. Note: 2003 Model adaptors may have 3/8″ boltholes.
(Tungsten carbide in the wings is an optional extra under part number PR92M-TW)

PR-91
20mm wide Knife point with Tungsten Carbide on leading edge.
Lucerne type point for pasture renovation and minimised disturbance of the soil.

PR 94-TW
Super Seeder 50mm wing with tungsten carbide leading edge and underside of wing.
Agronomic benefits of an Inverted-T seedbed with minimum disturbance and precise seed placement.

PR-94
With tungsten carbide leading edge only
Agronomic benefits of an Inverted-T seedbed in low abrasive soils with minimum disturbance and precise seed placement.